I recently set up 2x Fortigate 200B units to run in HA Active/Active mode, this posed a number of challenges:

1. HA doesn’t work if any interfaces use PPPoE or have an address assigned via DHCP
2. How do I effectively split our network communications between both units?

Challenge 1

The main problem was that both the internet connections used PPPoE for address assignment and auth – I had taken care of one of these previously as it was a simple ADSL link our Fortigate units didn’t allow for so we had a Cisco 837 box to terminate the PPPoE on a virtual interface and unnumber the static external IP to an internal interface. (Read: I used it as a proxy of sorts to get round hardware limitations).

We had done it before for an ADSL link so I follow the same methodology for our fiber link, except, with a faster Cisco box – in the form of a very simple, cheap Cisco 1841. Loaded the latest broadband firmware onto it (c1841-broadband-mz.151-4.M7.bin) and did the following:

• Assigned f0/0 to be our internal “gateway” address (assigned router address from BT/Zen in the static IP block)
• Assigned f0/1 to be our external WAN facing address and act as PPPoE client (no ip address)
• Created a virtual Dialer interface Dialer1 to act as PPPoE terminator
• Unnumbered Dialer1‘s IP against f0/0
• Set mtu to 1492 on Dialer1
• Enable ip cef
• Set adjust-mss to 1452 on f0/0 Extremely important to match frame size to ISP

Download full (nulled) config here.

With that out of the way I then set up our 200B to use this IP as its gateway (via static route 0.0.0.0/0.0.0.0 to go out [router address assigned to f0/0]).

A static route was used as I can set priorities on these and give our fiber link a higher priority than the ADSL meaning we will always use the fiber link unless it breaks, when it fails over to ADSL.

The previously configured PPPoE WAN link was changed to be “manual mode” and assigned it the desired public IP:

This then left me in a position where I could configure our 200B’s to use HA as now no interfaced relied on DHCP or PPPoE for addressing.

Challenge 2

“How do we effectively split our network communications between both units?”

This was considerably simpler than the first problem I came across – the answer is get a Gb switch – I had a Cisco 3560-X 24P-L to work with.

I split the ports into groups of 4 ports on VLANs (a separate untagged VLAN for each usable interface on the Fortigate) this gave me:

• 1x input port
• 1x output port to fw-a
• 1x output port to fw-b
• 1x extra port for maintenance access

Download full (nulled) config here.

Hence the groups of 4, if you had 3x or even 4x Firewalls in A/A HA then you would need 5 and 6 ports per VLAN respectively.

My show vlan output looked like this (note I am using jumbo frames):

Cisco-3560X-200B-HA#sh vlan

VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active    
2    lan                              active    Gi0/1, Gi0/2, Gi0/3, Gi0/4
3    mgmt                             active    
4    iscsi                            active    
5    phones                           active    Gi0/5, Gi0/6, Gi0/7, Gi0/8
6    wifi                             active    Gi0/9, Gi0/10, Gi0/11, Gi0/12
7    microwave-wan                    active    Gi0/13, Gi0/14, Gi0/15, Gi0/16
100  adsl                             active    Gi0/17, Gi0/18, Gi0/19, Gi0/20
101  fiber                            active    Gi0/21, Gi0/22, Gi0/23, Gi0/24
1002 fddi-default                     act/unsup 
1003 token-ring-default               act/unsup 
1004 fddinet-default                  act/unsup 
1005 trnet-default                    act/unsup 

VLAN Type  SAID       MTU   Parent RingNo BridgeNo Stp  BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1    enet  100001     1500  -      -      -        -    -        0      0   
2    enet  100002     9000  -      -      -        -    -        0      0   
3    enet  100003     9000  -      -      -        -    -        0      0   
4    enet  100004     9000  -      -      -        -    -        0      0   
5    enet  100005     9000  -      -      -        -    -        0      0   
6    enet  100006     9000  -      -      -        -    -        0      0   
7    enet  100007     9000  -      -      -        -    -        0      0   
100  enet  100100     9000  -      -      -        -    -        0      0   
101  enet  100101     9000  -      -      -        -    -        0      0   
1002 fddi  101002     1500  -      -      -        -    -        0      0   
1003 tr    101003     1500  -      -      -        -    -        0      0   
1004 fdnet 101004     1500  -      -      -        ieee -        0      0   
1005 trnet 101005     1500  -      -      -        ibm  -        0      0

All that needed to be done was plug the input ports into its respective VLAN and then take a cable to each 200B from each VLAN, effectively meaning each 200B could communicate with each input, easy.

In part 2 we will talk about setting up the Fortigate units themselves for HA and the proper procedure to employ for this.